Home / Processing Services / Plate & Sheet Processing / Dynamic Waterjet Cutting

Dynamic Waterjet Cutting

Penn Stainless offers stainless steel dynamic waterjet cutting in order to process complex part geometry.  Our stainless steel grades are well suited for dynamic waterjet cutting. Stainless plates thru 8″ thick can be dynamic waterjet cut.  Penn Stainless currently has 6 dynamic waterjet tables in order to reduce lead time.

Please send us your files,  so that we can quote your exact part. We accept PDF and CAD files, but DXF or DWG files are strongly preferred in order to provide you with the fastest service possible. Contact one of our specialists today!

Overview

Utilizing Penn Stainless Products’ Dynamic Waterjet® cutting technology to process your next stainless steel order will add tremendous value and cost savings to your bottom line with Lower Cost – Less Time By:

  • Eliminate secondary applications
  • Virtually eliminate taper left by standard w/j systems and plasma cutting methods
  • No heat affected zones to be machined
  • Improved cut tolerances
  • Higher processing speeds, which can lead to faster delivery
  • Less material loss during cutting. Less internal handling
  • Superior surface finish
  • Our Dynamic Waterjet table sizes are as follows:
    • Two Tables: 122" x 242"
    • One Table: 157" x 479"
    • One Table: 78.5" x 305"
    • One Table: 76" x 155"
    • One Table: 72" x 144"
  • Scribing capability for center marks and outlines.
History

In the 1950s, Dr. Norman Franz, a forestry engineer, attempted to use highly pressurized water to achieve a more efficient method for cutting lumber. He created high pressure by dropping heavy weights onto columns of water, and then proceeded to force the pressurized water through a tiny orifice. While his experiments showed that highly pressurized water could enable the cutting of wood and other materials, they did not result in a commercial product. Dr. Norman Franz could not overcome the obstacle of maintaining high pressure over extended lengths of time.


Development of Pure Waterjet Technology

It was not until the 1970s that technology developments enabled the introduction of the first commercial waterjet machines. These early machines were able to cut through a wide range of soft materials, including cardboard, food and foam rubber. There have been many improvements to this technology over the last few decades, but the basic mechanics are still in use today. Today, this process is referred to as “pure waterjet”. First, a pump pressurizes the water. Next, high pressure plumbing delivers the water to the cutting head and through a very small diamond or sapphire orifice, changing the pressure to velocity. At approximately 40,000 psi, the resulting stream that passes out of the orifice is traveling at Mach 2. And at 60,000 psi, the resulting stream is over Mach 3[i]. This supersonic stream creates the erosion force that cuts the material.


Development of Abrasive Waterjet Technology

Then, in 1979, Dr. Mohamed Hashish discovered a way to add abrasives, such as garnet, to the waterjet cutting process. The powerful waterjet stream accelerates the abrasive particles and those particles, not the water, cut the material. The abrasive waterjet is hundreds, if not thousands of times more powerful than a pure waterjet[ii]. It vastly expands the types of materials that can be cut. Abrasive waterjets can cut through hard materials, including stone, ceramic, stainless steel, and other metals. Flow International introduced the first commercial abrasive waterjet machine to the market in 1983.


Waterjet Machines for Cutting Stainless Steel Plate

Many of today’s waterjet machines include both pure and abrasive waterjet capabilities. Abrasive waterjet functionality is required for cutting stainless steel. In addition to the functionality described above to create high velocity particles capable of cutting through stainless steel, today’s machines also include plumbing that enables freedom of movement to the cutting nozzle. The cutting nozzle is typically integrated into motion equipment, which allows for complex geometric shapes and designs to be cut. Also, typically PCs or CNC controllers are used along with CAD/CAM software to translate dimension requirements into a digitally programmed path for the cutting head to follow.


Recent Advancements

Over the past few decades, there have been numerous advances to waterjet technology that continue to improve the product. These include improvements to the pump technology, programming capabilities, 3D functionality, motion equipment, and technology to improve the quality of cuts at higher speeds. The most significant recent advancement is based on Dynamic Waterjet® Technology, which was invented and patented by Flow International in 2001. Dynamic Waterjet technology counters stream lag and taper, two negative attributes associated with conventional waterjet technology. Dynamic waterjet technology has revolutionized waterjet cutting, and enabled it to compete more easily with other high end cutting techniques.


[i] “Waterjet White Paper.” Www.flowwaterjet.com. Flow International, 2002. Web. 28 Nov. 2011
[ii]Abrasive Waterjet Cutting | Abrasive Cutting for Hard Materials: Flow Waterjet.Flow Waterjet Cutting Machines & Products, UHP Pumps, HyperJet. Web. 06 Dec. 2011.

Choosing Waterjet

Selecting Dynamic Waterjet Technology to Cut Stainless Steel Plate and Sheet

Dynamic Waterjet® machines are an excellent choice for cutting stainless steel plate and sheet due to the fact that they use a cold cutting process and put very minimal pressure on the cutting material. Still, before selecting this method, it is important to consider many factors, including cost, tolerance requirements, material size and thickness, desired edge quality, lead time, and also any additional processing that will occur after the cutting step.


Benefits of Dynamic Waterjet Technology when cutting stainless steel plate include:
  • No heat affected zone.
  • Very unlikely to cause warping or other distortions, as compared to other cutting processes.
  • Extremely versatile process, enables very detailed 2D/2.5D geometry.
  • Environmental friendly process.  No harmful substances.
  • Taper and stream lag are very minimal, virtually eliminating the need for secondary processing.
  • Thin cutting stream, resulting in narrow kerf
  • Dynamic waterjet enables tight part-to-part separation for nested parts
  • Low cutting forces (under 1 lb. when cutting)
  • If secondary processing or milling is required for extremely tight tolerances, there is no hardened edge to grind off.
  • Can be used to cut all stainless steel grades.
  • Particularly beneficial for heat sensitive grades, such as 17-4, 410, 420, and 440, because laser or plasma cutting may cause these materials to harden at the heat-affected zone.
  • Can be used to scribe center marks or outlines that are used to assist locating during welding or assembly.

Limitations of Dynamic Waterjet Technology when cutting stainless steel plate:

There may be situations in which an alternative cutting method better meets a customer’s objectives for such parameters as cost, tolerance, or edge finish, but there are no major limitations with the process itself.


Cost Factors to Consider when Comparing Processing Costs

In order to accurately determine the true cost of cutting when comparing processing options, it is important to consider the following:

  • Cutting Costs. Dynamic Waterjet cutting is a very desirable process. In comparison to the laser cutting, waterjet cutting costs are typically higher. Still, it should be noted that cutting costs tend to be similar between the two technologies for parts over 7/8” thick, especially in the case that there are a lot of geometries to be cut.
  • Material Costs. It is important to consider the cost for all material used, including the skeleton that is left behind after the cut. The skeleton weight is fairly minimal in the case of Dynamic Waterjet cutting, even for thicker parts.
  • Costs of additional processing requirements. If Dynamic Waterjet processes eliminate or reduce additional steps, this should be taken into consideration in the overall cost evaluation.

Also, in order to save costs, it may be beneficial for customers to consider additional processing that Penn Stainless can provide beyond cut-to-size processing. Depending on the precision level needed, Dynamic Waterjet processing at Penn Stainless may offer a cost efficient alternative to other high end methods available in machine shops.

Value Added

Comparison of Dynamic Waterjet vs. Conventional Waterjet Processing

The differences between standard or abrasive Waterjet cutting and Dynamic Waterjet® Cutting are visible to the eye.

Bottom of piece cut without Dynamic Waterjet (left) and bottom of piece cut with Dynamic Waterjet (right)

Standard abrasive waterjet cutting leaves a noticeable taper and corner “wash outs” on the underside of the cut piece, which creates the need for secondary operations. With Dynamic Waterjet Cutting, the piece is ready to use, saving valuable time and money. It is important to note that taper and stream lag can be minimized on all waterjet machines when machines are run at slow enough rates. Thus, the big advantage of Dynamic Waterjet is that it is able to cut virtually taper-free parts with improved tolerance, 25%-400% faster than a standard waterjet, depending on the application. In the past, waterjet users ran their machines at slower speeds to achieve acceptable tolerance levels and minimize taper. Other shops used different cutting methods such as laser, EDM, and CNC machining. Thus, by utilizing Dynamic Waterjet technology, Penn Stainless Products offers the ability to provide better cuts and tighter tolerances at competitive rates. As compared to conventional waterjet, Dynamic Waterjet provides the following benefits when run at production speeds.

Part cut at high speed without Dynamic Waterjet, showing taper (left) and Part cut at high speed with Dynamic Waterjet, showing the elimination of taper (right)

  • Virtually eliminates taper left by standard waterjet systems.
  • Intricate geometric parts can be cut more accurately
  • Improved cut tolerances
  • Higher processing speeds, which can lead to faster delivery
  • Less material loss during cutting
  • Superior edge finish (250 RMS or better)
  • May lead to the elimination of secondary processing steps

 

Tolerances & Sizes
Dynamic Waterjet Tolerances, Size & grades
Thickness Ranges 20 Gauge sheets thru 8” thick stainless can be waterjet cut
Waterjet Table Sizes Two Tables: 122" x 242" / One Table: 157" x 479" / One Table: 78.5" x 305" / One Table: 76" x 155" / One Table: 72" x 144"
Stainless Grades All Stainless steel grades. Including 300 series, 400 series, precipitation hardening stainless. Duplex stainless and nickel alloy can be waterjet cut.
Tolerances Part tolerances of ±.030” is standard. Tolerances may vary depending on thickness and grade. For non-standard tolerance inquire.

DFX and DWG files are preferred, however Penn Stainless also accepts PDF scanned drawings, CAD files, faxed drawings, or textual (i.e. descriptive) dimensions.

Dynamic Waterjet Plate Cutting System PDF
PlayWaterjet Cutting